PO Box 445, Park Holme, SA 5043
     Ph: 0417 820 307  Fax: (08) 8322 0622
     Email: sales@tama.com.au

http://www.lunamachinery.com.au/index.php?page=products&cat=end-millers

End Milling Machines

The following selection is a representative range of the machines we can supply.
Contact Us to find out which machine is best suited for your application!

LUNA EM 210

Manual End Miller


Replace expensive punch tools

  • 1.0HP 240v Motor
  • Large cutting capacity
  • 160mm cutter capacity
  • Manual clamps (Optional air clamps)
  • Spray mist lubricator
  • Fully enclosed hood
  • Adjustable depth gauge
  • 3 position tool holder for additional cutters
  • Full Sheet metal cabinet
  • Ideal for end notching

Accessories Upon Request

  • Infeed roller conveyor and stand

 

LUNA EM 215

This EM 215 Horizontal Slotting Machine is used in the Capral Genesis Fabrication Kit.

EM 215 Horizontal Slotting Machine

Semi-Automatic End Miller


Replace expensive punch tools

  • 1.5HP 415v Motor
  • Large cutting capacity
  • 160mm cutter capacity
  • Semi-auto blade feed
  • Pneumatic Clamps
  • Adjustable depth gauge
  • Spray mist lubricator
  • Pneumatic tool release
  • Adjustable depth stop
  • Fully enclosed hood
  • 3 position tool holder for additional cutters
  • Full Sheet metal cabinet
  • Ideal for end notching

Accessories Upon Request

  • Infeed roller conveyor and stand

Cutter-Set Assembly

LUNA HS215A/P3 Horizontal Slotting Machine Genesis Configuration

 Changing Cutter Set:

 To change the cutter set turn off the power to the machine. Make sure the cutter motor has fully

stopped turning before opening the safety cover to the plate cutter set.

Press the black quick mandrel release button and remove the lock washer from the spindle.

Pull the mandrel with the cutter set from the drive spindle.

Put the desired cutter set onto the spindle and orientate the mandrel so that it is locked for cutting.

Press the black quick mandrel release button and place the special lock washer onto the spindle

end so that the mandrel is locked securely to the spindle.

Close the safety cover so that the keyed safety switch is activated.

The horizontal slotting machine is ready for use.

 

To assembly, fine tune or change cutter sets:

 Turn off the power to the machine. Open the safety cover after the cutting spindle

has stopped turning.

Position the mandrel onto the assembly shaft located next to the drive spindle

under the safety cover.

Place cutters and spacers as required building up the cutter sets.

Observe the right cutting direction when assembling cutters sets.

To accurately set the right spacing with pre-selected spacers use a

vice to press and measure using an accurate venire caliper.

Assembly the cutter sets on the mandrel and secure with the

supplied nut – left hand thread.

 

Make sure that there is sufficient thread so that the cutters

and spacers are tight on the mandrel.

Use a spanner to tighten the nut normally.

Do not over tighten as that might damage the thread in time.

Make a test cut into the extrusion of a few mm to allow measuring

with a venire caliper.

Make sure that the aluminium extrusion is securely clamped

before operating the horizontal slotting machine.

Use spacer washers to adjust until the slots are in the required positions.

Once the positions of the slots are obtained use the depth stop to set the desired slot depth. 

 

 

 

Proposed Genesis Set-Up

Genesis Cutter-Set Assembly Configuration

The dimensions on the drawings below are nominal and might

require fine tuning to adjust to variations that might exist in the

cutter sets or Aluminium Extrusions.

The Genesis Cutter Sets are supplied preassembled and set to

nominal cutting dimensions.

Follow the instructions for Cutter-Set Assembly to adjust if required.

Perform trial cuts with all cutter-sets before you utilize the machine

for fabrication.

Examples only - full set with drawings available from LUNA Machinery.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

HOME PAGE - ABOUT US - SPECIALS - HAND TOOLS - PNEUMATIC PRESSES - DIE SETS & PRESS TOOLING
ALUMINIUM FABRICATING EQUIPMENT WOODWORKING MACHINES -  
MACHINE VISION SYSTEMS
- SPECIAL PURPOSE BUILT MACHINERY - OTHER SERVICES - CONTACT US

TAMA Tools & Machinery Pty Ltd trading as LUNA Machinery S.A. 5043
PO Box 445, Park Holme, SA, 5043
Ph: 0417 820 307   Fax: (08) 8358 5952
E-mail: sales@tama.com.au